1 Item Items
Warning: Last items in stock!
Engineering site links: https://www.enterpoint.co.uk/products/oem-industrial-and-automotive-boards/mulldonoch-2/
XilinxTM XC3S2000 SpartanTM-3 FPGA.
XilinxTM XC3S200A-1400A SpartanTM-3A FPGA. XC3S200AN also possible for secure applications.
Two 128 Mbit SPI Flash Memories. First one is used for configuration but has spare space for microprocessor code etc.. Device 2 is totally independent and free to use.
256Mbit, X32 SDRAM. 64-512 Mbit possible.
Mulldonnoch 2 has our enhanced DIL Headers with 3.3V and DGND(0V) power strips. There is also a dedicated regulator for each header that can be set by whatever primary module is plugged in (supporting modules only and one in specific location). This regulator can also be controlled by the Startup FPGA allowing circuits to be switched on/off for power management purposes. The regulator voltage/s also can be selected as appropriate bank I/O voltage/s on the Main FPGA.
The RHS DIL Header has a 34 high header giving 66 I/O. Top pins and inner pins are power (note orientation to bottom of board).
The LHS DIL Header has a 34 high header giving 66 I/O. Top pins and inner pins are power.
The TOP DIL Header shares some pins with other headers and other board features. Please check pinout usage carefully before using this header.
Mulldonnoch 2 has one Moel-Bryn socket for high performance expansion. Modules like our Swinyard 1 can be used in this socket.
32 bit, 33 MHz, 3.3/5V PC104+ interface (PCI) capable of being used for other bus standards or as 5V tolerant general I/O. This interface also support signals to allow board to operate as motherboard and to handle request/grants from add on boards such as our Hollybush 1, Hollybush 2 or other industry standard boards.
USB Serial Interface
FT232R based serial interface. When plugged into a PC etc. this appears as serial port (other modes possible too). PC drivers available from FTDI. This interface can also be used to remote boot or configure the Main FPGA.
Micrel KSZ8851SNL SPI Ethernet controller. This interface can also be used to remote boot or configure the Main FPGA.
There is a Maxim DS2502 fitted to the Mulldonnoch 2 to provide a unique MAC address. A second device site option is also available for applications that need 2 MAC addresses. Both devices are accessible though the Startup FPGA.
Two PS2 interfaces to support mouse and keyboard. If not used for PS2 eight 5V tolerant signals are available. Four of these signals have pullups to 5V to facilitate interfacing to 5V CMOS logic devices. This interface can also be used to remote boot or configure the Main FPGA.
Real Time Clock
DS1306 real time clock chip on board. Battery holder on board to support un-powered time keeping and data storage..
Two 3.3V 8 pin DIL oscillator sockets for user fitted clock modules. Fixed 32Mhz and 25MHz oscillators on board. RTC 32.7678KHz also available. Startup FPGA can multiply or divide any of these frequencies. All of these are connected to the startup FPGA and any 4 can be routed to the Main FPGA. A clock can also be supplied by FT232 USB chip but needs to be plugged into USB hosting device.
High Accuracy Clock(option)
1ppm 10MHz clock site supporting D75A-010.0 MHZ TCXO.
3 LEDs connected to Startup FPGA. 5 LEDs connected directly to Main FPGA.
8 DIP switches.
ZIF socket option to support ancilliary items like remote displays.
Mulldonoch 2 has several different ways in which it can be powered. Which can be used depends on your add on card requirements. Mulldonoch 2 itself is capable of operating from a single 5V supply.
Option1 - 2.1mm Power Jack.
Option2 - USB connector (make be limited by your USB host or power supply).
Option3 - Disk Drive connector.
Option4 - Enterpoint PC104 power card (12-48V input).
On board there are 6 amp switching regulators for 3.3V, 2.5V, 1.8V and 1.2V. There are also user configurable 1.2A regulators for each of the DIL Headers. There is also a LP2996 reference supply regulator.
There is a twin power structure allowing the board to idle in a low power mode and to wakeup and power the Main FPGA and PCI104 stack. This feature is available only in some source power options and configurations.
Standard 2x7 2mm programming header.